单极性步进电机控制器电路--Unipolar Stepper Motor Controller This is a very good integrated circuit. There is no need for any external glue logic to drive the circuit, there is only 2 pins to drive the motor, one for controlling the direction and the other to trigger the stepping pulses. It provides a very compact design that drives 5 or 6 or 8 wire stepper motors. The 5 or 8 wire stepper motors are treated as a variation on the 6 wire motor. That is, the 5 has the two common wires from the coils center taps joined inside the motor (saves joining them outside the motor), however some confusion may occur with the ends of the other coils as to which一体成型电感 joins with which, however trial and error to determine this will not hurt anything. In the 8 wire motor case the joined center taps will have to worked out by you. You will know which coil is joined to which coil, however experimentation may be required to determine polarity.  The resistors R1 & R2 are only necessary if the supply voltage to the motors is above 10 volts or so, and are really only necessary near max voltages and tuning the response times of the motor for high speeds. See data sheets for details. There should be very little problem getting hold of six wire motors that make the connections obvious. These motors are by far the most common 模压电感where any degree of power is required, e.g. in printers. Non-working dot matrix printers are fairly common now-a-days and the mo差模电感器tors in them are excellent starting points for experimentation. You will also get belts, pulleys and gears thrown in (may be even a power supply if your are adventurous). A very simple Printed Circuit Board Design 
Features of the chip:
1.5A Maximum Output Current
35 V Output Sustaining voltage
Wave-Drive, Two-Phase, and Half Step Formats
Internal Clamp Diodes
Output enable control
Power on reset
Internal Thermal Shutdown
Sequence Connections
Two-Phase Drive Sequence Pin 9 GND Pin 10 GND (Simplest choice)
Wave Drive Sequence Pin 9 5v Pin 10 GND
Half Step Drive Sequence Pin 9 GND Pin 10 5V This driver will allow you to scale up your project considerably as the power will be much greater with the bigger motors and higher voltages and currents. The draw back is that the engineering that goes along with them will also have to be more substantial. The larger stepper motors are very heavy for desktop models but will be very versatile for the larger experiment. Commercial Kit and Data Sheets
An excellent, high quality kit (Nos:109) to experiment with this driver can be purchased from
Wiltronics Research PTY LTD
5-7 Ripon St (North)
Ballarat 3350
AUSTRALIA
Phone (03)5331 1947
It provides a 5 volt regulated supply, indicator LED一体成型电感器s, 555 oscillator for pulses and miniature switches to control direction and stepping modes. Single step or free funning can be chosen as well full data sheets provided. They also provide data sheets with the circuit. Contact them for prices. While not the cheapest way to go it 电感参数is the best seen so far.
有没有人用matlab仿真PFC/interleaved PFC模拟/目前正在用matlab仿真数字开关电源电路，之前用的是PSIM仿真模拟开关电源，但感觉PSIM数字化功能太弱，所以用matlab/simulink仿真。但感觉matlab比较复杂，而且资料也少，有没有对mat 基于DM642的X．264编码器优化摘要：X．264编码器注重实效性，在不明显降低编码性能的前提下，降低编码的计算复杂度，摒弃了JM中一些耗时相对较大但对性能的提升影响很小的模块，因此嵌入式系统中常选用X．264编码器。移植到DSP平台 BUCK电路给电池充电MOSFET管驱动电流怎么算啊? 如题,给电池充电，还不是接地。。。
一般的有说用表里Qg的，还有什么看QGTotal Gate Charget图看的，到底该怎么算啊?
围观学习
|
在线客服1号